About transistor multi function test instrument:
Test instrument using 3.7V rechargeable lithium battery (battery type: 14500) power supply of portable design, while the use of MINIUSB type T socket on the battery charging and system power supply, in a long time in the interior of the more economical and easy to replace the battery always to replace the economic investment!
The test instrument is stable and can be used to read out the data accurately and conveniently. It can be used for the electronic enthusiasts, electronic developers, designers, and electronic maintenance. Can test in line devices, can also test the patch element, which can be measured diode, transistor, SCR, MOS field effect tube; to judge the type of device, pin polarity, output HFE, threshold voltage, field effect transistor junction capacitance, additional conditions can measuring capacitance and resistance. Especially suitable for transistor matching and hybrid surface mount component identification.
* One key measurement operation, the time delay automatically shut off power. Support battery operation.
* Automatic detection PNP And NPNB ipolar transistor, N, PChannel MOSFET,JFET Field effect transistor, diode, double diode, thyristor, resistance, capacitance, inductance. Automatic detection pin definition.
* Current amplification factor for measuring the bipolar transistor (B) and the conduction voltage of the emitter.Uf). Darlington transistor can be identified by high threshold voltage and high current amplification factor.
* Bipolar transistor can be detected and MOSFET The internal protection diode is displayed on the screen.
* Measurement MOSFET Threshold voltage and gate capacitance values.
* Support for the measurement of two resistance, potentiometer can also be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the two ends of the pin.
* Resolution of resistance measurement is0.1Ohm, the maximum value of the measurement 50MOhm.
* Capacitance measurement range 25pf To 100mF(10000UF). Resolution of up to1 pF, inductance measurement range is 0.01MH-20H, otherwise it will be shown as a resistor if the inductance of the DC resistance is higher than that of the 2100Europe will also show resistance.
* Can detect 2UF The equivalent series resistance of the capacitor ESR Resolution is0.01Ohm. This function is very important for the detection of capacitance performance.
* Can display the correct direction of the symbol of the two diodes, while showing the forward voltage drop.
* LED The positive pressure drop is higher than the normal value of the diode. Double light emitting diode detector for double diode. Detection of light emitting diode will be shining.
* Each time the test is about two seconds, only a large capacitance and inductance measurement will take a long time.
Short three test end, into the test, the screen prompt correction steps. When off prompt open short circuit time to cut three test end school brigadier general to, when prompted to please in 1-3 feet above access 100nF capacitance.Access100nF Above the non polarity capacitor After the program will automatically enter the next step. Until the end of the correction to restart, you can complete the correction.
Main parameters and usage instructions:
1 UseATmega328 Micro controller
2 Super 12864 Graphics LCD test results.
3 One key operation, automatic power off power.
4 Exclusive to increase the power switch, to avoid storage and off when the battery power.
5 Automatic detection PNP And NPNB ipolar transistor, N, PChanne lMOSFET, JFET, diode, double diode, thyristor,Controllable silicon.
6 Automatic detection pin layout.
7 The current amplification factor and the threshold voltage of the emitter junction are measured.
8 Darlington transistor can be identified by high threshold voltage and high current amplification factor.
9 Bipolar transistor, MOSFETDetection of protective diode.
10 Measurement MOSFET Threshold voltage and gate capacitance values.
11 Support for the measurement of two resistors and symbols, the top four digits and the unit display. The display of the resistance sign at both ends is connected to the tester probe number (1-3). So potentiometer can also be measured.
12 Resolution of resistance measurement is 0.1 Highest measurement value 50MOhm.
13 A capacitor can be detected and measured. Top four digit and unit display. Values can be from 25pf(8MHz Clock50pF@ 1MHz Clock) to100mF. Resolution of up to1 pF(@ 8MHz Clock.
14 Can be right 2UF The equivalent series resistance of the capacitor ESR Capacitance measurement. Resolution 0.01Ohm.
15 Can be measured at the same time2A diode, and display correct pin layout and forward voltage drop.
16 LEDThe forward voltage drop is much higher than normal. Double light emitting diode detector for double diode.
17 Zener diode can be detected, if the reverse breakdown voltage is lower than the 4.5V. Will be shown as two diodes.
18 Only a single measurement is needed to find out the connection of the whole bridge.
19 Could not detect lower than 25pf Capacitor, but can be in parallel with a diode or greater than 25pf Capacitor parallel. The measurement results can be subtracted from the parallel capacitor value.
20 Resistance lower 2100Ohm will measure the inductance, the range will be from 0.01mH--20HBut the precision is not good.
21 The test time is about two seconds,Capacitance and inductance measurement can be extended with the increase of the value of the time.