Free shipping To
If you think the price is too high, please click to apply for lower price
1. Fixed turn the lamp current constant value of 0.1 times (when charging is used to identify whether the battery is full); 2. Benchmarks using a dedicated IC, and high-precision sampling resistor, so constant and more stable (20 degrees to 60 degrees constant temperature drift 5A when less than 5%), especially for LED driven 3. Output current, maximum output current can reach 8A, to meet most needs. 4.4 High-frequency capacitance, reduce output ripple, improve stability 5. Dual heat sink design, MOS tube Schottky diodes separate heat sinks, heat, independently of each other 6. At the cost of using large-size Kool toroid, improve work efficiency, and Use copper wire and Rao, reduce heat and improve efficiency. More than 7.3296 turn potentiometer, voltage and current regulation of high accuracy, good stability. 8. High stability dedicated current sense resistor current sampling accuracy, temperature drift of small, LED essential. 9. Color indicator, working status, charging necessary. 10. Voltage and current can be adjusted, adjustable power to do good effect, 8A current, power enough. Battery charging to use: 1. Make sure you need to charge the battery float voltage and charging current, the input voltage of the module; 2. Constant adjustment potentiometer, the output voltage is regulated to about 5V. 3. 10A current with a multimeter measuring the output short-circuit current block, while the constant current potentiometer allows to adjust the output current reaches a predetermined charge current value; 4. Constant adjustment potentiometer allows the output voltage reaches the float voltage; 5. Connected to the battery, try to charge. LED constant current driver to use: 1. Make sure that you need to drive LED operating current and maximum operating voltage; 2. Constant adjustment potentiometer, the output voltage is regulated to about 5V. 3. 10A current with a multimeter measuring the output short-circuit current block, while the constant current potentiometer allows to adjust the output current reaches a predetermined LED working current; 4. Constant adjustment potentiometer allows the output voltage reaches the maximum operating voltage LED; 5. Connect the LED, test machine.
|Material||Glass fiber + plastic + iron|
|English Manual / Spec||No|
|Other Features||Input voltage: 7~32V; Output voltage: adjustable (0.8~28V); Output Current: Approx. 8A (power tube temperature exceeds 65 degrees please add cooling fan, 24V switch within 12V 6A, open environment can generally be without fan) Constant current range: 0.2~8A (adjustable) Turn lamp current: constant current value * (0.1), turn the lamp current and constant value linkage, such as constant current value of 3A, turn the lamp current is set to a constant current of 0.1 times (0.1 x 3A = 0.3A), when the constant 2A, when adjusted to current value, then turn the lamp current constant current of 0.1 times (0.1 * 2A = 0.2A). Low pressure: 1V Output Power: Maximum power is about 300W, power tube temperature exceeds 65 degrees please add fan. Conversion efficiency: up to about 95% (output voltage higher, the higher the efficiency) Operating frequency: 300KHz; Output ripple: 20M bandwidth of Input 24V Output 12V 5A ripple around 50mV (excluding noise) Operating temperature: Industrial grade (-40 to +85) (please note the actual use of the power tube temperature, high temperature heat strengthened please) No-load current: Typical 20mA (24V switch 12V) Load regulation: +/- 1% (constant) Voltage regulation: +/- 1% Constant accuracy and temperature : the actual test , the module temperature changes from 25 degrees to 60 degrees , the change is less than 5% of the current value ( current value 5A) Dynamic response speed: 5% 200uS Potentiometer adjustment direction : clockwise ( increase ) , counterclockwise ( decrease ) is close to the input voltage regulating potentiometer (CV), close to the output of the potentiometer to regulate current (CC) Indicator: color indicator, charging indicator light red, light green fully charged (No load is green) lights without constant red. Output short circuit protection: Yes, constant current (constant current setting value) Input Reverse Polarity Protection: None, Output preventing backflow: None. Wiring: Terminal|
|Dimensions & Weight|
|Dimensions||2.56 in x 1.89 in x 0.91 in (6.5 cm x 4.8 cm x 2.3 cm)|
|Weight||2.33 oz (66 g)|
|1 x Module|
To enable volume discounts on this site, use coupon code: BULKRATE during checkout. You will see a discount applied at the bottom of the shopping cart. Competitive pricing is available. Contact us for details.
|Quantity||3+ units||5+ units||10+ units|
|Rate||US$7.86 shipped||US$7.83 shipped||US$7.80 shipped|
What is Bulk Rate? BulkRate is a semi-wholesale system with items priced separately from retail. When you use bulk rates, a flat $1.70 registered air mail fee will automatically be added to your cart to ensure delivery of package. While BulkRate's intention is to offer cheaper prices when you buy in bulk, because it is priced separately it on occassions show a higher than retail price. That's why we ask you to enter BULKRATE as a coupon code to manually activate the rates. You can always opt not to use the bulk rates. If you are looking for wholesale prices please feel free to contact us.
Looking to get even more?