DX  » view all rs232 module » rs232 module

rs232 module

Customers Who Bought rs232 module Also bought

Welcome to our rs232 module online shop. DX is an E-commerce online retailer situated in China with more than 100,000 cool gadgets with free worldwide shipping. Enjoy all these products that we have prepared for you.

rs232 module Customers Reviews

  • Good Cheap Module, Real RS-232 Output

    posted by cjketle

    A bit more info that might be useful. Startup report is:$PSRFTXT,Version:GSW3.2.4_3.1.00.12-SDK003P1.00a $PSRFTXT,Version2:F-GPS-03-0612201$PSRFTXT,WAAS Disable$PSRFTXT,TOW: 63708$PSRFTXT,WK: 1766$PSRFTXT,POS: 3943341 -144434 4994336$PSRFTXT,CLK: 94282$PSRFTXT,CHNL: 12$PSRFTXT,Baud rate: 4800 Appears to be version of EM-408 with RS232 (not TTL) output & firmware from 2006/7 ish.Measured current consumption 40-45ma @ 3.2v.Disabled if EN line is grounded.Connects direct to COM port for setting up with SiRFDemo.
    Works with external active antenna OK.
    Good cheap module but watch interface levels.
  • top usb ttl converter module

    posted by hhornbacher

    * works with windows/linux out of the box* supoorts 3,3/5V to power little projects on breadboard* good quality of product itself (no solder gaps, clean surface)
    I've used a ftdi chip usb-ttl-converter, I see no diffences in working with both, most important for me was the linux support, which they have both.
    If you need a cheap USB-TTL converter I can really recommend this device to you. Tested with several development boards, routers and selfmade projects.
  • RS232 convertetr for CubieBoard, Raspberry Pi etc.

    posted by Andrevs

    Contains MAX3232 RS-232 Line Driver Receiver.Converts RS-232 to levels between 3 and 5.5 Volt, which should be supplied on the Vcc line. Therefore it can be used with most boards. I am currently using it with my CubieBoard, but it should work fine with a Raspberry Pi as well. (I haven't tried it yet)
    Very handy device to connect CubieBoard, Raspberry Pi, etc. to a real RS-232 port.
    RS-232 to serial converter for 3 to 5.5 Volt.
  • RS-232 Transceiver Breakout Board

    posted by 4ndre

    Nicely built 9.5x16mm PCB with MAX3232 CSE+ (16PIN SO Package 3.0 to 5.5V) and the respective 0.1µF plus VCC capacitors.This is the recommended setup for this component.Small form factor, you can easily put it in an existing project.
    Very useful for interface with today 'all USB' and legacy RS-232 devices. You'll need to check the datasheet of 'MAX3232'In the top is the RX2/TX2 on the bottom RX1/TX1, in all the sides is the VCC + GND.
    Definitely worth the price, I would buy more of this items!
  • RS232 Serial port to TTL converter

    posted by hrpanchal

    It is easy to use this converter. simple, tiny and good thing is that it comes with necessary plugin wires for power and data.If you want to hookup your micro-controller to other micro-controller devices, this converter works excellent. I recommend to buy this product as easy to setup. Also, there are two LED on board for Rx/Tx which shows transfer of data.
    very useful for microcontroller
    simple, tiny and good thing is that it comes wit

WHY CHOOSE DX.COM?

Get great weekly deals and offers like: Collections